Open Access Open Access  Restricted Access Subscription or Fee Access

Advent in Dynamic Recovery of Dislocation Cusps: Especially for Loosely Tangled Dislocations

Prantik Mukhopadhyay

Abstract


Steady state dynamic recovery Kinetics is defined to quantify dislocation density during macro and micro-scale ausforming. High-stress regime of ausforming is liable to follow the rate controlling dynamic recovery kinetics of thermal glide by rapid advancements of kinks. Crystallographic orientation,  specific Taylor factor,  is observed to increase the work-hardening induced dynamic recovery. Stacking fault energy,  is found to be inversely proportional to. Distance covered by kinks,  is expressed as dislocation spacing of opposite signs. Crystallographic texture component S is found to be dynamically recovered faster than Goss orientation.


Full Text:

PDF

References


Y. Wang, T. Lei, J. Liu. “Tribo-metallographic behavior of high carbon steels in dry sliding: I. Wear Mechanisms and their transition”. Wear. June 1999; 231 (1): 12-19.

Y. Wang, T. Lei. “Wear behavior of steel 1080 with different microstructures during dry sliding”. Wear. 1996; 194 (1-2): 44-53.

N. Jin, P. Clayton. “Effect of microstructure on rolling/sliding wear of low carbon bainitic steels”. Wear. 1997; 202(2): 202-207.

W. Gong, Y. Tomota, Y. Adachi, et, al. “Effects of ausforming temperature on bainite transformation, microstructure and variant selection in nanobainite steel”. Acta Materialia. 2013; 61 (11): 4142–4154.

W. Gong, Y. Tomota, S. Harjo, et, al. “Effect of prior martensite on bainite transformation in nanobainite steel. Acta Materialia. 2015; 85: 243–249.

H. Beladi, I. B. Timokhina, Y. Estrin, et, al. “Orientation dependence of twinning and strain hardening behaviour of a high manganese twinning induced plasticity steel with polycrystalline structure”. Acta Materialia. 2011; 59 (20): 7787–7799.

R. Ueji, Y. Takagi, N. Tsuchida, et,al. “Crystallographic orientation dependence of ε martensite transformation during tensile deformation of polycrystalline 30% Mn austenitic steel”, Materials Science and Enggineering: A. 2013; 576: 14–20.

R. Freiwillig, J. Kudrman, P. Chraska. “Bainite transformation in deformed austenite. Metallurgical Transactions A. 1976; 7: 1091-1097.

K. Tsuzaki, T. Ueda, K. Fujiwara, T. Maki. “Increase in retained austenite by ausforming in an austempered silicon steel”. In: Proc. of 1st Japan Int. SAMPE Symp. Exhib. (ed N Igata), Japan, 1989, pp. 799-804.

P. H. Shipway, H. K. D. H. Bhadeshia. “Mechanical stabilisation of bainite”. Materials Science and Technology. 1995; 11 (11): 1116-1128.

R. H. Larn, J. R. Yang. “The effect of compressive deformation of austenite on the bainitic ferrite transformation in Fe-Mn-Si-C steels”. Materials Science and Engineering: A. 2000; 278 (1-2): 278-291.

J. He, A. Zhao, C. Zhi, H. Fan. “Acceleration of nanobainite transformation by multi-step ausforming process”. Scripta Materialia. October 2015; 107: 71–74.

J. P. Hirth, J. Lothe, Theory of Dislocations. Second ed., John Wiley & Sons, New York, 1982.

Z. Sun, S. Van Petegem, A. Cervellino, et, al. “Dynamic recovery in nanocrystalline Ni”. Acta Materialia. 2015; 91: 91–100.

G. Dieter, Mechanical Metallurgy. SI Metric ed., McGraw-Hill, London, 1988.

W. Gong, Y. Tomota, M. S. Koo, Y. Adachi. “Effect of ausforming on nanobainite steel, Scripta Materialia. 63 (2010) 819–822.

A. S. Argon, W. C. Moffatt, “Climb of extended edge dislocations”. Acta Metallugica. 29 (1981), 293-299.

Prantik Mukhopadhyay. Advanced Quantitative Analysis of Dynamic Recovery during Warm Working of FCC Alloys, Journal of Materials & Metallurgical. 2022; 12(1): 1-15.

P. Mukhopadhyay. “Fabrication of AA5182-Semis for Precise Components”. Journal of Materials & Metallurgical. 2021; 11 (3): 21-32.

Prantik Mukhopadhyay. “Constitutive Equations for Microstructural Features Developed During Solid Particle Erosion of 52100 Steel. Defence Science Journal. 2020; 70 (4): 448-453.

P. Mukhopadhyay, P. S. Kannaki, M. Srinivas, Manish Roy. “Microstructural developments during abrasion of M50 bearing steel”. Wear. 2014; 315(1-2): 31-37.

P. Mukhopadhyay, M. Srinivas, Manish Roy. “Microstructural developments during erosion of tribological steels”. Materials Characterization. 2016; 113: 43-51.

P. Mukhopadhyay, R. Goyal, M. Roy. “Dynamic Hardness Trend of Tribological Steels Used for Advanced Power Transmission Assembly”. Journal of Aerospace Engineering & Technology. 2021; 11(2): 55-69.

Prantik Mukhopadhyay. “Work Hardening Trend of Aluminum Alloys from Non- Deformable and Deformable Particles”. Journal of Aerospace Engineering & Technology. 2021; 11(3): 1-13.


Refbacks

  • There are currently no refbacks.


eISSN: 2231-038X